![]() Note: The following assumes the current password is root123 and the new password is root1234 substitute for these as appropriate.įirst start both servers using UniController and proceed as follows: ![]() Setting a new MySQL root password using MySQL Prompt requires two root accounts to be changed along with one configuration file. Set New MySQL root user password using MySQL Prompt This is purely for convenience and one of consistency. Note: The above root user accounts all use the same root password. Run phpMyAdmin and verify that the MySQL server is accessible. Clear your browser's cache and restart the servers. Replace root12 with the new root password root123. Edit file C:\UniServerZ\htpasswd\ passwd.txt.Note: Do not stop the MySQL server at this point. Navigate to the end of the Privileges User Overview page and click reload the privileges link.Repeat step 2) for the remaining user (3). ![]() Click Go (6) to unpdate the user's password.Scroll down the page to Change passwordįor example root123 (4) repeat password (5).Click the first Edit Privileges (2) which opens a new page: "Edit Privileges: User". ![]() The user privileges page opens, as shown on right: From the top menu bar of phpMyAdmin, click the Privileges (1) button.To change the password proceed as follows: Note: The following assumes the current password is root12 and the new password is root123 substitute for these as appropriate.įirst start both servers using UniController and then start phpMyAdmin. Setting a new MySQL root password using phpMyAdmin requires two root accounts to be changed along with one configuration file. Set New MySQL root user password using phpMyAdmin Note: Clicking the cancel button no action is taken. The Set New MySQL Password menu opens (See image on right).Starting UniController provides the first opportunity to change the current root password, it is highly recommended that you set this password at the first opportunity.Īlternatively you can skip setting a new MySQL root password and run this menu option later using: Set New MySQL root user password using UniController Set New MySQL root user password using MySQL Prompt.Set New MySQL root user password using phpMyAdmin.Set New MySQL root user password using UniController.Restart the MySQL server: $ sudo /opt/bitnami/ctlscript. If your stack ships an older version of MySQL, use this command: $ sudo /opt/bitnami/mysql/bin/mysqld_safe -pid-file=/opt/bitnami/mysql/data/mysqld.pid -datadir=/opt/bitnami/mysql/data -init-file=/tmp/mysql-init 2> /dev/null & If your stack ships MySQL v8.x, use this command: $ sudo /opt/bitnami/mysql/bin/mysqld_safe -pid-file=/opt/bitnami/mysql/data/mysqld.pid -datadir=/opt/bitnami/mysql/data -init-file=/tmp/mysql-init -lower_case_table_names=1 2> /dev/null & Stop the MySQL server: $ sudo /opt/bitnami/ctlscript.sh stop mysql TIP: Check the MySQL version with the command /opt/bitnami/mysql/bin/mysqladmin -version or /opt/bitnami/mysql/bin/mysqld -version If your stack ships MySQL v5.6.x or earlier, use this content: UPDATE er SET Password=PASSWORD('NEW_PASSWORD') WHERE User='root' If your stack ships MySQL v5.7.x, use this content: ALTER USER IDENTIFIED BY 'NEW_PASSWORD' If your stack ships MySQL v8.x, use this content: ALTER USER IDENTIFIED BY 'NEW_PASSWORD' ĪLTER USER IDENTIFIED BY 'NEW_PASSWORD' If you don’t remember your MySQL root password, you can follow the steps below to reset it to a new value:Ĭreate a file in /tmp/mysql-init with the content shown below (replace NEW_PASSWORD with the password you wish to use). $ /opt/bitnami/mysql/bin/mysqladmin -p -u root password NEW_PASSWORD Replace the NEW_PASSWORD placeholder with the actual password you wish to set. You can modify the MySQL password using the following command at the shell prompt. NOTE: When setting a new password, avoid the use of special characters or quotes, as this can sometimes cause issues when accessing the database through shell scripts. The output of the command indicates which database server (MySQL or MariaDB) is used by the installation, and will allow you to identify which guides to follow in our documentation for common database-related operations. To identify which database server is used in your stack, run the command below: $ test -d /opt/bitnami/mariadb & echo "MariaDB" || echo "MySQL" On account of these changes, the file paths and commands stated in this guide may change depending on whether your Bitnami stack uses MySQL or MariaDB. NOTE: We are in the process of modifying the configuration for many Bitnami stacks.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |